GIRAFFE
Textures:
DESCRIPTION
  Dilution: all JUNGLE decorative paints are ready for use and must be shaken well before and during use. Application temperature: between +5°C and +30°C. Strength: when the paint has fully hardened, a breathable film develops which offers good resistance to knocks and normal abrasion. Washability: 15 days after the cycle has been applied, the surface acquires its definitive properties, becoming breathable and washable with water or common neutral detergents. Equipment cleaning: use water. Storage: make sure that the can is tightly closed, even after use, and store at temperatures between +5°C and +30°C. Stability: approximately 2 years. SPECIFIC SAFETY INSTRUCTIONS: avoid direct contact with skin. Protect eyes and face. In the event of contact, rinse immediately and thoroughly with water and consult a doctor. Do not wash equipment in watercourses, drains, etc. USER ADVICE: N.B.: the information provided here is, to the best of our knowledge, correct and accurate. However, given that the conditions in which the products are used are not under our control, we will not be held liable for any recommendations or advice we provide. All products required for creating the JUNGLE effect are sensitive to different painting techniques therefore it is important that the painting work is carried out entirely by same person. Moreover, it is essential to follow the application instructions specific to each JUNGLE Range effect. Shades may vary compared to the catalogue by between 20% and 30%, as well as from one batch to another, thus it is advisable to carry out a small test before commencing the work.The manufacturer and the distributor shall not be held liable for possible variations between batches, or in cases where the batch number is illegible. Should the batches be different, all the material must be mixed in a large container before beginning application, in order to avoid differences in colour once the product has been applied. Check the stencils supplied with the JUNGLE KIT thoroughly before positioning them. In particular, check the quantity and integrity of the stencils to ensure the correct outcome of the desired decorative effect.
TECHNICAL SHEETS

 

African atmospheres

The Giraffe finish brings the essence and atmosphere of the African continent into your home. The warm colours of this coat make every room stylish and welcoming, enriching it with a slightly wild and subversive air

JUNGLE Decorative Paints can be applied to various surfaces including cement (new or old), plasterboard, plaster of Paris, wood (new or old), plastic, glass and iron (new or old), provided they are free of humidity, well dry, smooth and have already been treated.
Any loose or dusty paint, as well as any grease or rust, must be removed and the surface washed with suitable soap. Fill the surfaces to be decorated, if necessary, and apply a base coat that is suitable to the type of surface to be treated. Once the base coat is dry, apply the JUNGLE Range products as indicated below:
1) PRIMER 700 IVORY 10. (Coverage 0.080 l/sqm) Apply a coat using a wool roller. Allow to dry for 4 hours at 20°C, then proceed to Point 2.
2) MZ 600 TRANSPARENT. (Coverage 0.140 l/sqm) Apply two coats using a wool roller. Allow the first coat to dry for about 2 hours at 20°C before applying the second coat. Allow to dry for another 2 hours at 20°C then proceed to Point 3.
3) GF 608 already coloured. (Coverage 0.080 l/sqm) Apply a thick coat of paint with the 10 - 20 cm wool roller over the entire surface to be treated; avoid joints from forming and do not retouch the decorated surface even if still wet. Allow to dry for about 2 hours at 20°C, then proceed to Point 4. 4) MZ 600 TRANSPARENT. (Coverage 0.140 l/sqm) Apply two coats using a wool roller. Apply the first coat and leave to dry for about 2 hours at 20°C.
Apply the second coat of MZ 600 TRANSPARENT and leave to dry for 2 hours at 20°C then proceed to Point 5.
5) Place the GF 5E STENCILS over the entire surface to be decorated and align the connection points between the various stencils. Complete the process and proceed to Point 6. 6) GF 609 already coloured. (Coverage 0.110 l/sqm) Apply a coat of paint with the 10 cm wool roller over the entire surface covered with the GF 5E STENCILS.
Remove the stencils and allow to dry for about 1 hour at 20°C before proceeding to Point 7.
7) VALFLOK 300 TRANSPARENT. (Coverage 0.200 l/sqm) Apply two coats using a wool roller and spread well. Allow to dry for about 1 hour at 20°C before applying the second coat.
N.B.: All the above-mentioned phases must be completed without interruptions once they are started, while any areas that have already been coated must not be retouched.
GIRAFFE JUNGLE KIT: There are two JUNGLE KITS available in order to obtain the GIRAFFE effect to decorate 3 sqm or 10 sqm.
PRODUCTS INCLUDED IN THE 3 SQM GIRAFFE JUNGLE KIT: 0.270 l of PRIMER 700 IVORY 10 - 0.900 l of MZ 600 TRANSPARENT - 0.500 of GF 608 - 0.300 of GF 609 - 0.550 l of VALFLOK 300 TRANSPARENT - 12 x GF 5E STENCILS - N . 1 ADIPIT 500 PV 73.
PRODUCTS INCLUDED IN THE 10 SQM GIRAFFE JUNGLE KIT: 0.900 l of PRIMER 700 IVORY 10 - 3 l of MZ 600 TRANSPARENT - 1.700 l of GF 608 - 1 l of GF 609 - 1.800 l of VALFLOK 300 TRANSPARENT - 36 x GF 5E STENCILS - N . 1 ADIPIT 500 PV 73.”.

FINISH DETAILS
INSPIRATIONS
FIND A STOCKIST
APPLICATION VIDEO
RECEIVE OUR CATALOGUE
Google+ HTML 4.01 Valid CSS Page loaded in: 0.055 - Powered by Simplit CMS